Buat Sendiri Kabel RS232 DIGSI ke Relay SIPROTEC 4

Apakah anda punya masalah seperti ini?

Punya Relay Proteksi SIPROTEC 4 seperti gambar dibawah, punya softwarenya juga (DIGSI 4), tetapi tidak dapat mengkomunikasikan dari laptop ke relay…

image

Ini adalah beberapa trik mudah yang mungkin dapat membantu permasalahan anda.

imageLangkah pertama, pastikan port RS232 di komputer anda berfungsi dengan baik. Apabila laptop anda tidak dilengkapi dengan port RS232, anda dapat membeli kabel “USB to RS232” seperti dibawah ini, harganya tidak mahal dan banyak tersedia di toko komputer.

.

.

Install CD driver USB-232 ke komputer. Setelah instalasi selesai, kita tidak dapat menghubungkan langsung kabel USB-232 ini langsung ke relay. Kenapa begitu? Dikarenakan port RS232 relay SIPROTEC posisi TX-RX nya di pin yang sama, sehingga diperlukan kabel CROSS atau menyilangkan pin TX dan RX di pin No 2 dan pin No 3. Anda dapat membeli kabel DIGSI ini ke Siemens langsung atau membuatnya sendiri.

Untuk Kabel CROSS ini dipasaran disebut dengan kabel NULL MODEM. Hanya saja kabel yang beredar di pasaran umumnya kepalanya adalah female-female atau cewe-cewe, sedangkan yang dibutuhkan adalah male-female. Ini dapat diakali dengan memasang gender changer male-male atau mengganti kepalanya dari cewe ke cowo.

Bagi anda yang mau sedikit berkreasi menyolder, saya sarankan anda membuatnya sendiri seperti gambar dibawah ini konfigurasinya:

Kabel DIGSI / SIPROTEC

clip_image002

Anda cukup membeli DB9 male dan female 1pcs sepasang, kabel isi 2 dengan shield atau bisa juga kabel audio isi 2 dengan serabut tembaga menyelubungi diluar. Berikut adalah contoh peralatan yang dibutuhkan

Image result for audio cable twisted shieldedimageimage

Jadilah kebel DIGSI kita

image

Sekarang sambungkan kabel yang kita buat tadi ke kabel USB-232, kemudian sambungkan ke relay dan laptop menggunakan kabel tersebut. Buka software DIGSI 4 dan cobalah koneksikan dengan klik kanan terus pilih “Plug & Play”, apabila berhasil maka proses bar download muncul dan anda bisa masuk ke setting.

image

Selamat berkreasi dan semoga bermanfaat.. -red

Baca Keseluruhan Isi Posting Ini >

How To Integrate SIPROTEC Relay/BCU to NARI Automation System

The advantages of using DIGSI 4.86 or higer version is more easier to creater report control block and in a single dataset may contains more than one report control block in a single click. Unlike in DIGSI 4.84 or lower version, each dataset is for one report control block.

clip_image002
But, in DIGSI 4.86 or higher version, the common problem during import SCL (CID or SCD) to another vendor HMI or Gateway is XML parse error. In this case, I’ll show you the thing that you have to do before importing CID file from SIPROTEC BCU or SIPROTEC Relays to NARI HMI and NARI RTU/Gateway successfully.

First, configure dataset and its contents (all signals which needed) and create the report (one report served one client such us HMI and Gateway). After finish the configuration, export the CID.

clip_image004
Second, before importing the CID to NARI HMI or NARI Gateway, you should edit the CID file and remove/delete unnecessary “Private” node in the CID file. You may use notepad++ or XML Notepad

clip_image006
In Notepad++, find and remove all section from <Private up to </Private>. And please don’t miss delete the other parts, otherwise the CID file will damaged or corrupt.
I suggest you to use XML Notepad to do this task, more safe and more easier for you. Download and install XML Notepad on your PC. Launch the XML Notepad and open the CID file.
Find all unnecessary Private folders

clip_image008

clip_image010

Push Delete button and search again using F3 button, Repeat deleting the Private folder until there’s no Private folder anymore.

clip_image012

Save the CID file then import it to the NARI HMI and NARI Gateway. You should have no more error during import the CID file. Thank God! Now all my SIPROTEC IED was successfully connected to NARI SAS.

If you still have any problem or question related to this subject, please don’t hesitate to contact me

Regards,
Ari Sulistiono | www.arisulistiono.com | Substation Automation Engineer | Siemens EM DG Promoter

Baca Keseluruhan Isi Posting Ini >